What this checklist is for

Forklift attachments change how a truck handles loads. Clamps, sideshifters, rotators, fork extensions, booms, push-pulls, and other attachments need checks for mounting, locking, leaks, damage, controls, and capacity information before use.

A forklift can pass a basic truck inspection while the attachment creates the real risk. Loose mounting hardware, damaged forks or extensions, missing pins, hydraulic leaks, or capacity plate mismatches can affect load control.

This checklist is a practical worksheet, not legal advice, not a government document, and not a guarantee of compliance. Match it to your equipment, workplace, procedures, and qualified safety review.

Printable PDF checklist template

Use this page when the inspection need is about forklift attachments, not the base truck alone. It adds mounting, capacity, control, and hydraulic prompts to the daily checklist.

  • Truck ID, attachment type, attachment ID, operator, date, and shift.
  • Mounting, locking, pin, hook, chain, clamp, extension, and visible damage checks.
  • Hydraulic hose, fitting, cylinder, leak, and control checks where applicable.
  • Capacity plate, load chart, label, and manufacturer instruction prompt.
  • Defect note, removed-from-service decision, and reviewer signature.

Use the browser print command to print this page or save it as a PDF. Treat the printed sheet as a starting template, then edit fields so they match your equipment, manufacturer instructions, workplace hazards, and company procedure.

Suggested checklist items

  • Attachment type and ID are recorded with the truck ID.
  • Mounting points, hooks, pins, locks, chains, or brackets are present and secure.
  • Fork extensions, clamps, rotators, sideshifters, booms, or other load-contact parts show no unsafe damage.
  • Hydraulic hoses, fittings, cylinders, and couplers show no visible leak or damage where equipped.
  • Controls operate smoothly and return as expected.
  • Capacity plate, load rating, labels, and instructions are present and legible where required by procedure.
  • Any attachment defect is recorded and reviewed before use.

How to use this form

Use the sheet as a pre-task prompt and record. The most useful forms are specific enough to guide the worker but short enough to complete during a normal shift. Keep the completed record with maintenance, inspection, or supervisor files according to your company's procedure.

  • Complete the base forklift inspection first.
  • Add the attachment section whenever an attachment is installed or changed.
  • Confirm capacity information and controls match the installed attachment.
  • Report any loose, damaged, leaking, unlabeled, or uncertain attachment condition.

Recommended frequency

Before use when an attachment is installed, changed, or suspected damaged.

Frequency should increase when equipment is shared, conditions change quickly, or a finding repeats. A small business can start with one routine form and then split it into area-specific forms once patterns become obvious.

Common mistakes to avoid

  • Inspecting the truck but not the installed attachment.
  • Using fork extensions without checking retention or condition.
  • Ignoring capacity plate changes after attachment installation.
  • Leaving a damaged attachment available because the truck itself passed.

Who should use it

Forklift operators, maintenance teams, supervisors, and shipping managers.

Supervisors should review completed forms for repeated defects, missing signatures, and findings that are marked but not corrected. A checklist becomes more valuable when it triggers follow-up instead of only filling a folder.

Source notes

The links below point to public safety resources used to shape the checklist topic. Requirements may vary by industry, state plan, equipment, and task. Review official sources and qualified guidance for your exact workplace.

FAQ

Should attachments be on the daily forklift inspection?

Yes, when an attachment is installed or used. Add attachment-specific checks to the truck inspection form.

Do fork extensions need inspection?

Yes. Check condition, retention, fit, labeling, and whether the extension is suitable for the load and truck procedure.

What should happen if an attachment leaks?

Record the leak, stop using the attachment if it may affect safe operation, and route it for qualified review.

Can one attachment checklist cover every attachment?

Use shared fields for mounting and defects, then add attachment-specific items for clamps, rotators, extensions, booms, or push-pulls.